Guide ยท 7 min read
The Best Images for Relief and Lithophane Printing
The converter can only work with the brightness it is given. A photo with clear light and dark separation becomes a crisp relief; a flat, dim snapshot becomes a gray slab. This guide shows which images work, which do not, and the quick edits that close the gap. One honest note first: if the photo is of an object you want to print whole, such as a chair or a lamp, no image edit will turn a relief into that object. FurniMesh (furnimesh.com), made by our team, generates a full 3D model from a furniture photo for that job.
What the converter sees
Strip the color out of any photo and you have what the converter reads: a grid of grays from 0 (black) to 255 (white). In Heightmap mode that range spreads across your relief height, 3.0 mm by default. In Lithophane mode it spreads across the thickness range, 0.8 to 3.0 mm by default. If your image only uses grays from 90 to 160, it only uses about a quarter of the available range, and the print looks shallow and soft.
So the first quality test is simple: open the image in any editor, look at the histogram, and check that it reaches close to both ends. If it bunches in the middle, the relief will too.
Images that convert well
| Image type | Heightmap relief | Lithophane | Notes |
|---|---|---|---|
| Side-lit portrait or pet | Fair | Very good | Shadows give the face shape when backlit |
| Landscape with sky | Fair | Very good | Bright sky becomes thin and glows |
| Black and white logo or text | Very good | Good | Use Invert if the logo is dark on white |
| Terrain elevation map | Very good | Fair | Brightness already equals height |
| Pencil or ink drawing | Good | Good | Clean the paper to pure white first |
| Dim indoor snapshot | Poor | Poor | Raise contrast and crop before converting |
| Busy group photo | Poor | Fair | Small faces fall below nozzle resolution |
The pattern is that reliefs reward strong shapes and clean edges, while lithophanes reward a full tonal range. A logo makes a better relief than a portrait; a portrait makes a better lithophane than a logo.

Subject size against the print size
Detail you can see on screen is not always detail the printer can draw. A 0.4 mm nozzle lays a line about 0.4 mm wide, so features narrower than about 0.5 mm on the finished print disappear. On a 100 mm wide panel, that is roughly 1/200 of the width. If a face in your photo is 30 pixels wide out of a 3,000 pixel image, it will be 1 mm wide on the print: an eye becomes a single sample. Crop so the subject fills most of the frame, or print larger. The scale and resolution guide has the numbers for other sizes.
Five edits that fix most photos
You can make these in any photo editor, including the free ones built into phones and operating systems. Save the result as PNG or high-quality JPG and load it into the converter.
Crop tight. Remove everything that is not the subject. Every millimeter of empty wall is a millimeter not spent on the face.
Stretch contrast. Use Levels or Curves to pull the darkest real area close to black and the brightest close to white. Avoid clipping large areas to pure white, which become flat plateaus.
Simplify the background. A bright, busy background competes with the subject. Darken or blur it for a relief; brighten it for a lithophane, where bright means thin and glowing.
Reduce noise. High-ISO grain turns into a rough, sandpaper surface. Apply light noise reduction in the editor, or use the converter's Smoothing slider: one pass for reliefs, zero to one for lithophanes.
Sharpen edges a little. Mild sharpening helps edges survive the sampling step. Heavy sharpening adds halos that print as ridges.
Make your own relief or lithophane STL. Free, and your image never leaves your browser.
Open the converterWorked example: a logo for a 120 mm wall plaque
You have a black logo on a white background, 1,600 by 800 pixels, and want a raised plaque. In Heightmap mode, bright is high, so as-is the white background would rise and the logo would sink. Turn on Invert so the black logo becomes the raised part. Set width to 120 mm, which makes the plaque 60 mm tall. Use a 2.0 mm base and 2.0 mm of relief so the logo stands 2 mm proud. At 300 samples across, samples sit 0.4 mm apart and the edges stay sharp. Leave Smoothing at 1 to soften the stair-steps on curves without rounding the corners away.
Check the preview from a low angle. If thin strokes in the logo look patchy, they are narrower than two samples; raise the resolution or thicken the strokes in the image. The heightmap versus AI guide explains why a logo works so well as a relief while a product photo does not.
Color photos and why they sometimes surprise you
The converter reads brightness, and colors that look very different can share the same brightness. A red rose on green leaves may convert into one even gray, because the red and green have similar luminance. Check the image in grayscale before converting: if the subject disappears, adjust it in the editor with a black-and-white filter that lets you weight the color channels separately.

When no image edit will help
If what you really want is the object in the photo, standing on its own, the problem is not the image. A heightmap can only ever give you a raised picture. For furniture and similar single objects, use an AI generator such as FurniMesh, then run its GLB through the GLB to STL converter. The furniture photo guide covers what makes a good source photo for that, which is a different checklist: plain background, even light, the whole piece in frame.
Questions
Does image resolution matter for an STL relief?
Only up to the resolution of the mesh. The converter samples at most 600 points across, so a 1,200 pixel wide image already carries more detail than the mesh can hold. Bigger files just take longer to load.
Should I convert my photo to black and white first?
You can, but you do not have to. The converter reads brightness from color images automatically. Editing in grayscale helps you judge contrast before converting.
When should I use Invert?
Use it in Heightmap mode when the subject is dark on a light background and you want the subject raised, such as black text on white paper. Lithophane mode already makes dark areas thick, which is what you want for backlit panels.