Made by the FurniMesh team. FurniMesh (furnimesh.com) is our own product, so we benefit when you use it. Details.

Guide ยท 7 min read

How to Make a Lithophane STL (With Print Settings)

Published and updated November 22, 2026 · By the Free Image to STL team (FurniMesh)

A lithophane is a thin panel that looks blank until you hold it up to light, then shows a photograph in soft gray tones. Making the STL takes seconds; getting a print that shows real detail depends on a handful of numbers. This guide gives you those numbers and explains each one. If what you actually want is a solid model of an object in the photo, such as a chair, a lithophane is the wrong format: FurniMesh (furnimesh.com), made by our team, turns a single furniture photo into a full 3D model instead.

How a lithophane works

Light passing through plastic fades with thickness. A 0.8 mm section of white PLA lets plenty of light through and reads as near white. A 3 mm section lets very little through and reads as dark gray. A lithophane maps each pixel of your photo to a thickness between those two limits: dark pixels become thick, bright pixels become thin. Under backlight the thickness map turns back into a picture.

The technique is far older than 3D printing. Porcelain lithophanes were made in Europe through the 19th century, and many survive as lamp shades, tealight domes and window panels.

A 19th-century porcelain lithophane panel showing a detailed scene
A mid-19th-century porcelain lithophane. The same rule applies to a printed one: thick areas read dark, thin areas read light. Photo: Unknown artist, Public domain, via Wikimedia Commons (source)

The four numbers that matter

The converter's Lithophane mode exposes four values. Its defaults are a sound starting point for a flat panel printed in white PLA on a 0.4 mm nozzle.

Lithophane settings and their effect
SettingDefaultUsual rangeWhat changes
Minimum thickness0.8 mm0.6 to 1.0 mmBrightest areas. Too thin leaves holes or pinpricks of glare.
Maximum thickness3.0 mm2.5 to 3.5 mmDarkest areas. More thickness gives deeper blacks but longer prints.
Width100 mm60 to 200 mmPhysical size. Height follows the image's aspect ratio.
Resolution250 samples across150 to 400Detail. Past the nozzle's limit it only grows the file.

The gap between minimum and maximum is your tonal range. At 0.8 to 3.0 mm you have 2.2 mm of range to spread across the whole gray scale. Shrinking it to 1.0 to 2.5 mm makes a flatter, lower-contrast image; widening it to 0.6 to 3.5 mm adds contrast but makes the thin end fragile.

Why the default resolution is 250

Resolution is how many height samples the converter takes across the width. At 100 mm wide and 250 samples, neighboring samples sit 100 / 249, or about 0.40 mm, apart. That matches the line width of a 0.4 mm nozzle, which is the smallest feature the printer can draw across the face of the panel. At 150 mm wide, raise the resolution to about 375 to keep the same spacing. Going finer than the nozzle cannot add visible detail; the scale and resolution guide works through the math and the file sizes.

The frame

A flat panel with a 0.8 mm edge is easy to chip and tends to curl at the corners. The converter adds a 4 mm border at full maximum thickness by default. It stiffens the panel, gives the slicer a solid perimeter to start each layer on, and frames the picture when lit. Keep it on unless the panel will slide into a lamp housing that already has its own frame, in which case check the slot width before you turn it off.

Worked example: a 100 mm landscape panel

Say you have a 4,000 by 3,000 pixel landscape photo and want a desk-sized panel. With the defaults the picture area is 100 mm wide and 75 mm tall, the frame adds 4 mm on every side, and the finished panel measures 108 by 83 mm. Its thickness runs from 0.8 mm in the sky to 3.0 mm in the darkest shadows and along the frame.

The picture area is sampled at 250 by 188 points, and the frame adds about ten more samples on each side, so the mesh lands a little over 110,000 triangles and the STL comes out under 6 MB. That is light for any slicer. The converter shows the exact triangle count and size above the Download STL button before you save.

Make your own relief or lithophane STL. Free, and your image never leaves your browser.

Open the converter

Slicer starting points

These values are widely used starting points for flat lithophanes in PLA on a 0.4 mm nozzle. Your printer and filament will shift them, so print a small 50 mm panel first if the photo matters.

Slicer starting points for a flat PLA lithophane
SettingStarting pointReason
OrientationStanding upright, picture facing youThickness steps are drawn by the nozzle path, not stacked layers
Infill100%Any gap in the panel shows as a pattern when lit
Layer height0.12 to 0.16 mmFiner layers reduce banding across the image
SpeedSlower than your default, around halfA tall thin part wobbles at speed
Brim5 to 8 mmKeeps the narrow base from tipping
FilamentWhite or natural PLA, matteEven light transmission, no tint

When you stand the panel up, the slicer sees a footprint only 3 mm deep and up to 108 mm long. A brim is the simplest way to keep it upright. Some people add a small foot in their slicer or CAD tool; either works.

A white 3D printed lithophane panel standing upright on a printer bed
A printed lithophane standing on the build plate, the usual orientation for a flat panel. Photo: EngineerForLive, CC BY-SA 4.0, via Wikimedia Commons (source)

Picking and preparing the photo

Lithophanes compress the image into roughly a dozen distinguishable gray levels, so photos with clear light and dark separation look best. Faces lit from the side, landscapes with sky and silhouettes, and pets against a plain background all work. Dim indoor shots with muddy midtones turn into a uniform gray slab. Raise contrast slightly before converting, and crop tight so the subject fills the panel. The image selection guide covers this in detail, including when to use the Invert toggle.

Leave Smoothing at 0 for lithophanes unless the photo is noisy. Smoothing averages neighboring samples, which removes grain but also softens edges that the backlight would otherwise show crisply.

Lighting the finished panel

Daylight through a window is the quickest check. For display, a warm white LED behind the panel gives even light without heat. Keep the light source at least a few centimeters behind the panel so it lights the whole area instead of a bright hotspot. Lamps built around printed lithophanes are a common project: the panel slides into a printed frame with an LED strip or bulb behind it.

A lamp with a 3D printed lithophane panel lit from inside
A desk lamp built around a printed lithophane panel. Photo: Maix79, CC BY-SA 4.0, via Wikimedia Commons (source)

Common problems and fixes

A panel that looks too dark overall usually has too much maximum thickness for the light you use; drop it to 2.5 mm. A washed-out image usually means the photo had little contrast or the minimum is too high. Visible horizontal bands come from inconsistent extrusion or a coarse layer height. Small holes in bright areas mean the minimum is too thin for your printer, so raise it to 1.0 mm.

If the image appears mirrored when lit, you are looking at it from the back. The converter lays the picture out so it reads correctly from the textured side, so face that side toward the viewer and put the light behind the flat back.

Questions

What thickness should a lithophane be?

A common range is 0.8 mm at the thinnest point and 3.0 mm at the thickest. Thinner than about 0.6 mm risks holes and light bleed; thicker than about 3.5 mm makes dark areas nearly opaque and slows the print.

Should I print a lithophane flat or standing up?

Standing upright is the usual choice. The nozzle then draws the thickness changes with its outline moves, which gives finer detail than stacking them as layers, and the layer lines run across the panel instead of stepping the image.

What color filament is best for lithophanes?

Plain white or natural PLA. Colored and glossy filaments tint the light or scatter it unevenly, and silk finishes show streaks.

Why does my lithophane look like a blank sheet?

You are looking at it in front light. A lithophane only shows its picture when light passes through it from behind, such as a window, a phone torch or an LED panel.